RAK811 WisNode-LoRa Arduino shield board

The following image is RAK WisNode-Lora development board，and it compatible Arduino development board, It also can be used as an extension board development with Arduino. The interface resource are as follow：

Connect the evaluation board to the computer via the Micro USB line， Through the computer serial port tool to send commands to the module.As shown in the following figure：

at+mode=0                    /* SET LoraWAN work mode */
OK

at+get_config=dev_eui         /* GET Dev_EUI check */ 
OK3037343644357402

at+set_config=app_eui:39d7119f920f7952&app_key:a6b08140dae1d795ebfa5a6dee1f4dbd 
/* SET LoraGateway app_eui and app_key , big endian*/
OK

at+join=otaa       /* Join OTAA type*/
OK
at+recv=3,0,0     /* Join status success*/

Welcome to RAK811

at+mode=0                    /* SET LoraWAN work mode */
OK

at+set_config=dev_addr:00112233&nwks_key:3432567afde4525e7890cfea234a5821&
                                   apps_key:a48adfc393a0de458319236537a11d90 
/* SET LoraGateway dev_addr nwks_key and apps_key , big endian*/
OK

at+join=abp       /* Join ABP type*/
OK

/*After join gateway success, then can send and receive data*/ 

at+send=0,2,000000000000007F0000000000000000 
/*APP port:2, battery level 50%, unconfirmed message*/
at+recv=2,0,0  /*unconfirmed mean tx success*/

at+send=1,2,000000000000007F0000000000000000 
/*APP port :2, battery level 50%, confirmed message*/
at+recv=1,0,0  /*confirmed mean receive ack from gateway*/

/*If gateway has data to send module, will receive date meanwhile ack */
at+recv=0,2,10,30313233343536373839 
/*APP port :2, receive size 10, hex:30313233343536373839*/

/* Module A Rx Side*/
Welcome to RAK811

at+mode=1                    /* SET LoraP2P work mode */
OK

at+rf_config=867700000,10,0,1,8,14 
/* SET LoraP2P Frequency:867.7MHz, SF10,Bandwith 125KHz, coding Rate:4/5, Preamlen:8, tx power:14dbm */
OK

at+rxc=1                    /* SET LoraP2P Rx continue enable report rx data */
OK

at+rx_stop                 /* If want stop Rx continue */

/* Module B Tx Side*/
Welcome to RAK811

at+mode=1                    /* SET LoraP2P work mode */
OK

at+rf_config=867700000,10,0,1,8,14  
/* SET LoraP2P Frequency:867.7MHz, SF10,Bandwith 125KHz, coding Rate:4/5, Preamlen:8, tx power:14dbm */
OK

at+txc=100,1000,800100000600010002da9557e142d9  
/* SET LoraP2P Tx continue ,100 packets, 1S interval, hex data */
OK

at+recv=9,0,0    /*When Tx complete */
at+tx_stop                 /* If want stop Tx continue */

To upgrade the Lora module, First we should make the module get into Boot mode. We should switch the P1 pin make the Boot pin connection with 3.3V Pin. Then reset the module, Operate according to the steps:

1.Open the Flash Loader Demonstrator tool，Set the serial port parameters;

2.Click the “NEXT” button, arrive the following interface;

3.The again the “Next” button，Choose STM32L1_Cat2-128K;

4.Choose “Download to device”，Set the path to the new firmware, and click “NEXT” button;

5.Upgrading;

6.Upgrade Successful.

• WisNode-Lora Quick Start Guide V1.2
• WisNode LoRa Schematic_20171129
• RAK811 Lora AT Command V1.4
• RAK811 Lora Module Datasheet V1.3
• RAK811 OpenMCU Developing User ManualV1.0
• How To Connect Lora RAK811 to The Things Network

• Getting Started With the RAK811 LoRa Node.pdf
• Getting started with the RAK 831 Lora Gateway and RPi3.pdf
• How To Connect Lora RAK811 to KotahiNet.pdf
• How To Connect Lora RAK811 to The Things Network.pdf
• How to Connect LoRa RAK811 to Actility.pdf
• How to Connect LoRa RAK811 to Cayenne.pdf
• How to Connect LoRa RAK811 to LORIOT.pdf

• Flash Loader Demonstrator.zip
• ReleaseNotes_20171106.txt
• V2022.zip

• LoRa Module 3D File.zip
• RAK811 Lora Module Datasheet V1.3.pdf
• WisNode LoRa Schematic_20171129.pdf
• WisNode-LoRa Package Design Reference.zip

• How to Use Lora-Shift Board.pdf
• RAK811 Lora AT Command V1.4.pdf
• RAK811 OpenMCU Developing User ManualV1.0.pdf
• The documents indicate the LC Circuit in WisNode-Lora .pdf
• WisNode-Lora Quick Start Guide V1.2.pdf

• CH340 Drive.rar